介電常數/介質損耗測試儀GDAT-B

介電常數及介質損耗測試儀讀書清晰,無須換算,操作簡便,特別適合電子元器件的質量分析,品質控制,科研生產,也可用于高校的電子信息,電子通信,材料科學等專業作科研實驗儀器.

介電常數/介質損耗測試儀特點：
◆ 優化的測試電路設計使殘值更小
◆ 高頻信號采用數碼調諧器和頻率鎖定技術
◆ LED 數字讀出品質因數，手動/自動量程切換
◆ 自動掃描被測件諧振點，標頻單鍵設置和鎖定，大大提高測試速度

作為一代的通用、多用途、多量程的阻抗測試儀器，測試頻率上限達到目前高的160MHz。

1 雙掃描技術 - 測試頻率和調諧電容的雙掃描、自動調諧搜索功能。

2 雙測試要素輸入 - 測試頻率及調諧電容值皆可通過數字按鍵輸入。

3 雙數碼化調諧 - 數碼化頻率調諧，數碼化電容調諧。

4 自動化測量技術 -對測試件實施 Q 值、諧振點頻率和電容的自動測量。

5 全參數液晶顯示 – 數字顯示主調電容、電感、 Q 值、信號源頻率、諧振指針。

6 DDS 數字直接合成的信號源 -確保信源的高葆真，頻率的高精確、幅度的高穩定。

7 計算機自動修正技術和測試回路*化 —使測試回路 殘余電感減至zui低，** Q 讀數值在不同頻率時要加以修正的困惑。

標準配置：
高配Q表 一只  
試驗電極  一只 （c類）
電感      一套（9只）
電源線    一條
說明書    一份
合格證    一份
保修卡    一份

使用方法：

高頻Q表是多用途的阻抗測量儀器，為了提高測量精度，除了使Q表測試回路本身殘余參量盡可能地小，使耦合回路的頻響盡可能地好之外，還要掌握正確的測試方法和殘余參數修正方法。

1．測試注意事項

a．本儀器應水平安放；

b．如果你需要較精確地測量，請接通電源后，預熱30分鐘；

c．調節主調電容或主調電容數碼開關時，當接近諧振點時請緩調；

d．被測件和測試電路接線柱間的接線應盡量短，足夠粗，并應接觸良好、可靠，以減少因接線的電阻和分布參數所帶來的測量誤差；

e．被測件不要直接擱在面板頂部，離頂部一公分以上，必要時可用低損耗的絕緣材料如聚苯乙烯等做成的襯墊物襯墊；

f．手不得靠近試件，以免人體感應影響造成測量誤差，有屏蔽的試件，屏蔽罩應連接在低電位端的接線柱。

2．高頻線圈的Q值測量（基本測量法）

Characteristic
The design of test circuit optimization so that the residual smaller
The high frequency signal by digital tuner and frequency locking technique
The LED digital readout quality factor, manual / automatic range switching
Auto scan the measured resonance frequency standard, single set and lock, greatly improve the test speed
Item
GDAT-B
Frequency range
10kHz ~ 50MHz
Frequency segmentation
(virtual)
10 ~ 99.9999kHz
100 ~ 999.999kHz
1 ~ 9.99999MHz
10 ~ 60MHz
Frequency indicating error
3 * 10-5 + 1 words
As the latest generation of general, multi-purpose, multi - range impedance test instrument, the test frequency limit to reach the highest 160MHz.
Double scanning, automatic tuning and searching function of 1 double scanning technology - testing frequency and tuning capacitor.
2 the input of the two test elements - the test frequency and the tuning capacitor value can be input by the digital key.
3 double digital tuning - digital frequency tuning, digital tuning capacitor.
4 automatic measurement technology - automatic measurement of the Q value of the test piece, the frequency and the capacitance of the resonant frequency.
5 the parameters of liquid crystal display, digital display, Q main capacitor, inductance value, signal source frequency, resonant pointer.
6 DDS direct digital synthesis signal source to ensure high Baozhen source, high stability and high precision, amplitude and frequency of the.
7 computer automatic correction technology and testing circuit optimization - the test circuit residual inductance to the lowest, the total eradication of Q read the value at different frequencies to be corrected by the confusion.
Standard configuration:
A table with Q
Test electrode (c)
Inductance one set (9)
Power cord
Instruction manual
Certificate of conformity
Warranty card
Using method
High frequency Q table is multi-purpose impedance measurement instrument, in order to improve the measurement accuracy, in addition to the Q table test loop itself residual parameters as much as possible, so that the frequency response of the coupling loop is as good as possible, but also master the correct test method and residual parameter correction method.
1 test note
A. the instrument should be placed horizontally;
B. If you need a more accurate measurement, please put on the power supply, preheat 30 minutes;
C. regulates the main capacitor or main capacitor digital switch, when close to the resonant point please slow tune;
The D. is the connection between the test piece and the test circuit wiring should be as short as possible, thick enough, and should be in contact with good, reliable, in order to reduce the resistance and the distribution parameters caused by the measurement error;
E. is not directly placed on the top of the panel, the top of the top of a centimeter above, when necessary, the use of low loss of insulation materials such as polystyrene, etc.;
F. hand shall not be close to the test piece, lest the human body sensor affect the measurement error, and there is a shield of the test piece, and the shield cover should be connected to the terminal of the low potential.
2 high frequency Q measurement (basic measurement method)