深圳市菲益科電子科技有限公司
深圳市菲益科電子科技有限公司
| 參 考 價 | 面議 |
產品型號neoVI FIRE2
品 牌
廠商性質其他
所 在 地深圳市
百分零部件網采購部電話：0571-88918531
QQ:2568841715
聯系方式：查看聯系方式
更新時間：2024-12-16 12:12:05瀏覽次數：60次
聯系我時，請告知來自 百分零部件網neoVI FIRE 2提供8個CAN/CAN FD通道、4個LIN通道和1個以太網(Ethernet)通道，所有通道可同時運行，帶硬件時間戳；USB電器隔離，是一款全功能的總線通訊接口和數據記錄儀。
neoVI FIRE 2 英特佩斯產品，下一代汽車多總線通訊接口和數據記錄儀 基于現有的CAN和LIN網絡，下一代車輛網絡將會擴展以太網（Ethernet）和CAN FD，neoVI FIRE 2提供1個以太網（Ethernet）通道、8個CAN/CAN FD通道和4個LIN通道，所有通道同時運行，帶硬件時間戳；USB電器隔離，是一款全功能的總線通訊接口和數據記錄儀，一經推出，在汽車行業獲得一致的好評。 ● 8個CAN/CANFD通道； ● 4個LIN通道，LIN1.X，LIN2.X和J2602； ● 1個以太網（Ethernet），DoIP/XCP； ● 所有通道可同時工作，硬件時間戳； ● 所有協議的報文收發功能； ● USB電器隔離，不損害電腦。 General Specifications Fourth-generation neoVI architecture: over 10x the performance of earlier devices Low power consumption Power Supply: 4.5-40V operation LED membrane keypad: 10 full-color LEDs indicate network status; 2 LEDs for legacy status; 2 user buttons Temperature Range: -40°C to +85°C On-board UPS power supply for safe shutdown of data logger Vehicle connectors: 26-pin male HD D-Sub and 9-pin micro D-Sub One-year limited warranty Field-upgradeable flash firmware General Purpose IO: 2 MISC IO (0-40V) – can be configured as Analog/PWMIO General purpose I/O rate report interval: 10 Hz to 1 kHz, or based on digital change Microsoft-certified USB drivers USB Host for neoVI MIC GPS or powering RAD-Moon accessory Isolated high speed (480 Mb/s) USB Standalone mode Including scripting, receive messages, transmit messages, expressions, I/O and transport layers J2534 and RP1210 A/B compatible for CAN/ISO15765, Keyword and ISO9141 microSD card slot support for up to 128 GB of storage (or the limit of newer SDHC cards). The removable card is formatted using FAT32 for PC compatibility Battery backed real time clock (RTC). Timing Specifications 64-bit timestamping to an accuracy of 10 microseconds on CAN and LIN networks with no overflow. Accuracy of 0.5 microseconds possible if using only one network Simultaneous operation on all CAN/LIN networks Transmit message double-buffering on all networks, allowing back-to-back message transmission Network Specifications – CAN 8x CAN (FD) Channels (NON ISO CAN FD with free upgrade to dual ISO/NON ISO support in 2016) 6 Dedicated ISO11898 Dual Wire CAN FD Physical Layer (MCP2561FD) 2 CAN with CAN mode and 3 software-selctable PHY options DW CAN mode: 2 dedicated ISO 11898 Dual Wire CAN FD physical layers (MCP2561FD) LSFT CAN mode: 2 Low Speed Fault Tolerant CAN physical layers (TJA1055) SW CAN mode: 2 Single Wire CAN physical layers GMW3089 / SAE J2411(MC33897) CAN FD support on all dual wire channels Up to 1 Mb/s software-selctable baud rate for arbitration phase (auto baud capable) Up to 8 Mb/s software-selctable baud rate for data phase (auto baud capable) Listen-only mode support Single Wire High Speed Mode, Test Tool Resistor, and High Voltage Wakeup support Two software programmable DW CAN termination circuits Network Specifications – LIN 4x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line Full support for LIN 1.X, 2.X and J2602 LIN J2602 / 2.X compatible physical layer Software enabled 1K LIN Master Resistor per channel LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors LIN Bus Master Mode operates at same time as LIN Bus Monitor LIN Bus Slave simulation – with or without an LDF file LIN Bus hardware schedule table with support for LIN diagnostics UART-based state machine Programmable timing parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution) Initialization waveforms including Fast Init, Five Baud, and Custom Software-selctable baud rate Logic analysis mode to discover low level LIN or K Line errors Network Specifications – DoIP / XCP / Automotive Ethernet 10/100 Ethernet PHY with low power mode Compatible with BroadR-Reach® with RAD-Moon Ethernet Converter Accessory Software controlled DoIP activation line * Specifications subject to change. Please contact Intrepid for the latest information.
neoVI FIRE 2主要功能
離線記錄儀，腳本運行和ECU仿真
除了作為一個通訊接口，neoVI FIRE 2還可以在離線模式下工作，其內嵌系統可以運行實時腳本，將記錄的數據保存在microSD卡中，并模擬ECU和網關的功能。有了這些功能，可以進行ECU刷新工作，定制刷寫腳本將microSD卡中的數據下載到ECU中。
neoVI DLL，J2534，Linux和RP1210支持
由于有些用戶需要定制開發自己的上位機軟件，neoVI FIRE2支持三種開放的API：neoVI DLL API，SAE J2534 API和TMC RP1210 A/B。該neoVI DLL API包括了所有流行的開發環境的例子，包括C＃，VB.NET，VB6，Delphi，C ++ Builder，Visual C ++，LabVIEW和LabWindows。而且提供Linux操作系統的示例和驅動程序，而且提供API函數，允許第三方調用neoVI FIRE2，將其作為一個硬件密鑰來使用。
Vehicle Spy軟件應用
我們的Vehicle Spy支持neoVI FIRE 2，通過Vehicle Spy軟件進行總線數據和發送，所有網絡可同時運行； 可在Vehicle Spy中對neoVI FIRE 2進行腳本配置和下載，使neoVI FIRE2成為一個獨立運行的數據記錄儀和仿真器；用戶可以利用強大的接口優勢，加載DBC、LDF等數據庫，編寫和調試Fuction Block腳本，并將腳本下載到設備中。
硬件在環實時仿真功能
neoVI FIRE 2包含實時腳本引擎，可離線運行Function Block腳本，工程師創建一個腳本程序下載到硬件中運行，允許微秒級的時間誤差，可滿足更精確的測量和控制。通過硬件加速的功能，Vehicle Spy也可配置neoVI FIRE 2為實時發送的設備，如周期報文，總線數據回放，或?qū)崟r腳本。
數據記錄儀功能
neoVI FIRE 2能夠?qū)⒉杉綌?shù)據存儲在內置的microSD卡中，存儲卡經過嚴格的實時性、存儲速度、和故障測試，采用安全的FAT32的存儲系統，讓您的數據更加可靠。neoVI FIRE 2在每一幀報文中添加硬件定時的時間戳，達到微妙級的精度，絕不丟失任何細節，讓您的數據更加精確；在Vehicle Spy通過腳本配置觸發、過濾和判斷條件，讓您的記錄儀更加靈活和智能，neoVI FIRE 2擁有一個強大的電源管理系統，可通過Vehicle Spy靈活配置休眠和喚醒條件。
相對代neoVI FIRE的改進
在代neoVI FIRE的基礎上，neoVI FIRE 2主要增加了新的車載網絡CAN FD和Ethernet以太網支持，性能比代產品neoVI FIRE更加強大，主要改進功能包括：
● 更強壯的接插件；
● 更大的腳本空間；
● 支持通過USB口讀取SD卡數據；
● 更寬的供電范圍（4.5V-40V）；
● 腳本配置時只需USB供電；
● MISC I/O口電壓范圍（0-40V）
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
百分零部件網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
